Suzuki 800 Intruder Club & Forum A UK Site Dedicated To The Suzuki C800, VL800, VX800, M800, VZ800, VS800, C50, M50 Model Intruder / Boulevard / Marauder |
| | Sachs 800 PAIR valve removal | |
| | Author | Message |
---|
RonB58 Prospect
| Subject: Sachs 800 PAIR valve removal Fri Feb 14, 2020 5:59 pm | |
| Hi all, my bike has been running rough so I decided to clean out the carbs before balancing them. I needed to replace a pilot jet in the rear carb and it behaved beautifully once I richened the mixture. The front carb was losing back pressure and causing backfires so I investigated the PAIR system. It uses an induction valve operated by vacuum from the front cylinder with the take off line on the inlet manifold. Once I removed the vacuum line from the induction valve and blocked it the bike ran like a dream, no backfire and carbs balanced perfectly. My question is have any other Sachs owners removed this or do they know what bike it is off? It is a Denso valve operated by vacuum. I also removed the PAIR lines from the exhaust ports and fabricated two blanking plates. I think the Suzuki 800s use a solenoid with a feed from the ECU whereas the Sachs uses a more antiquated and illogical system!
Ron | |
| | | adilmon Member
| Subject: Re: Sachs 800 PAIR valve removal Fri Mar 13, 2020 9:59 am | |
| - RonB58 wrote:
- Hi all,
my bike has been running rough so I decided to clean out the carbs before balancing them. I needed to replace a pilot jet in the rear carb and it behaved beautifully once I richened the mixture. The front carb was losing back pressure and causing backfires so I investigated the PAIR system. It uses an induction valve operated by vacuum from the front cylinder with the take off line on the inlet manifold. Once I removed the vacuum line from the induction valve and blocked it the bike ran like a dream, no backfire and carbs balanced perfectly. My question is have any other Sachs owners removed this or do they know what bike it is off? It is a Denso valve operated by vacuum. I also removed the PAIR lines from the exhaust ports and fabricated two blanking plates. I think the Suzuki 800s use a solenoid with a feed from the ECU whereas the Sachs uses a more antiquated and illogical system!
Ron Hi Ron I've done this on my Sachs Roadster 800. I used the PAIR blanking kit made for a VS800/VL800/VZ800 and it fit perfectly. The Valve an plumbing are in a box somewhere in case I have a pedantic MOT tester. I cleaned out my carbs too, after my bike was sat for a while, and currently trying to unstick the from pilot screw. These bikes have different carb settings to other suzuki 805cc engines (just look at the variety of factory setting variations for VX800 and you'll know what i mean), but I did buy a Sachs OEM workshop manual from their administrators. Most of the pics in there are from the VS800 manual, but I'll post a few pages from carb section next week. | |
| | | RonB58 Prospect
| Subject: Re: Sachs 800 PAIR valve removal Fri Mar 13, 2020 11:08 am | |
| Glad to hear I'm not the only one! I had to run the rear carb richer to get the balance correct on the Carbtune. Looking forward to the pics and thanks!
Ron | |
| | | Sponsored content
| Subject: Re: Sachs 800 PAIR valve removal | |
| |
| | | | Sachs 800 PAIR valve removal | |
|
Similar topics | |
|
| Permissions in this forum: | You cannot reply to topics in this forum
| |
| |
| |
Slide Show | A random selection of suzuki800.com member bikes. |
Latest topics | » Hello All, by Badger Yesterday at 10:56 pm
» G’day by Badger Yesterday at 2:37 pm
» Hi all by Badger Yesterday at 2:33 pm
» just saying hello to this site by sgtruth60@gmail.com Tue May 07, 2024 8:04 pm
» Newbie by M800chimp Tue May 07, 2024 11:28 am
» 12inch apes by Mbroom21 Tue Apr 16, 2024 12:54 pm
» Aye what's happenin'? by 717RedRumBob Fri Apr 12, 2024 6:50 am
» Handle bars rotation for comfort by Badger Thu Apr 11, 2024 1:20 pm
» Hello! by GregWidger Mon Apr 01, 2024 9:16 pm
» Hey to all by alongfortheride Tue Mar 26, 2024 9:41 pm
» Just saying hello as asked... plus a question. by SAM11206 Wed Mar 20, 2024 6:34 pm
» Hello! by Onigatudor Wed Mar 20, 2024 2:39 pm
» Choke plunger by flying1 Wed Mar 13, 2024 4:43 pm
» Hello intruder people by nano Tue Mar 05, 2024 2:19 pm
» Hi from North east England by Brianhuck Sat Mar 02, 2024 7:30 pm
» VX800 - Wiring issue colours & diagram? by Billybop90 Fri Mar 01, 2024 12:44 am
» Looking for a set of Leg wind deflectors for a C50 Boulivard. by Aikido789 Sat Feb 24, 2024 10:11 am
» Saying hello from Cheshire by bernard chaddock Wed Feb 21, 2024 4:58 pm
» ola de portugal by fabio almeida Tue Feb 20, 2024 9:28 am
» Hello from Texas by icoolwecool99@gmail.com Mon Feb 19, 2024 9:47 pm
|
|